57 not categorized PORSCHE 356 A SUSPENSION KITSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2005-08 (includes uncategorized and accessory items) FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection 11590099101 This suspension cancellation kit eliminates the Porsche active suspension management (pasm) warning light and persistent trouble codes when installing a conventional suspension kit. The functioning of the of the electronic control unit remains completely intact and Porsche dynamic chassis control (pdcc) is also fully functional. Warning: if the pasm is switched off with the Porsche tester (pwis), the pdcc is also deactivated!
$506.00
Make a selection 291681 Sport spring kits are h&r's number one selling product. Enhance the look of your vehicle with a reduced fender well gap. H&r sport springs lower the vehicle center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, h&r sport springs are the number one upgrade for your vehicle. General FitmentBOXSTER 2005-08
$451.35
Make a selection 11590099701 Necessary for adding a manually adjustable coil over suspension kit to a car with pasm. This kit cancels the factory damper signal in order to prevent an error signal / code.
$519.20
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection FVD343986PSS9 Only for vehicles equipped with bilstein suspension pss9/10. General FitmentCAYMAN 2009-12CAYMAN 2006-08 BOXSTER 2009-11 BOXSTER 2005-08 BOXSTER 1997-04
$2,046.79
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection BBI9965010002 • provides additional rear toe adjustment
$875.00
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection BBI9964010001 Features
$525.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection S1116RDL For a perfect fit, reliability you can depend on, full adjustability, and optimum performance, the factory GT3 swaybar is the best on the market. We have packaged them together with new bushings and our adjustable drop links to provide you with a wining combination. The light weight hollow 26.8mm od sway bars are half the weight of a solid bar with the same stiffness. Complete with fully adjustable front drop links to eliminate suspension preload. Correctly sized, precision, teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. No wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends. All necessary hardware is provided in zinc ...(choose a part on the right to read more) General FitmentBOXSTER 2005-08CAYMAN 2006-08
$450.95
Make a selection S1117 For a perfect fit, reliability you can depend on, full adjustability, and optimum performance, the factory GT3 swaybar is the best on the market. We have packaged them together with new bushings and our adjustable drop links to provide you with a wining combination. The light weight hollow 26.8mm od sway bars are half the weight of a solid bar with the same stiffness. Complete with fully adjustable front drop links to eliminate suspension preload. Correctly sized, precision, teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. No wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends. All necessary hardware is provided in zinc ...(choose a part on the right to read more) General FitmentBOXSTER 2005-08911 2005-08 911 GT3 2007-11 CAYMAN 2006-08
$625.95
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.55
Make a selection 1306107997 Our billet aluminum strut mounts are a must when upgrading to a race suspension such as moton or bilstein pss9/10. The OEM units flex and move during cornering which causes spongy handling characteristics. Our engineered mounts will add more precise handling and road feel. Each of our components are cnc machined from 6061-t6 aluminum, assembled with stainless steel spherical bearings and hard anodized. General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08
$827.63
Make a selection 11595B01EIB Lowering up 30mm, front axle load 1290kg / 1340 rear, 1475 kg with trailer operation. Not for vehicles with level control/air suspension.
$686.40
Make a selection FSBA22 The light-weight hollow sway bars are half the weight of a solid bar with the same stiffness. they are fabricated from aircraft-quality 4130 chrome moly alloy steel and heat treated to maximize strength and reliability.
$495.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |